On a static-free surface, remove the top cove …. AvertX Go! See here for more information. Other cameras have newer hardware and higher capacities. Check your camera's specifications doc …. AVI and MP4 files are a commercial format for digital video files and are compre …. Once you have set up your recorder for remote access, you can use your smart phone or tablet to access your recorder with AvertX GO!
HD for the iPad or A …. Windows 10 introduced Microsoft Edge as its default web browser. This browser does not support ActiveX. Microsoft continues to install Internet Explorer 11 with Windows 10 and also has a way to switch ….
NOTE: Multiple cameras can be selected simultaneously by pressing and holding the Control button on the keyboard and the right button on the click on the mouse as each camera is highlighted. If the camera has obtained a ProConnect IP address on the To view the upload progress, click on the cloud at the top right-hand side of the menu, located on the right side of the account name. To view uploaded videos: Click on the arrow pointing upward at the top right-hand side of the menu, located on the left side the account name.
Click on the Videos icon on the left hand side of the connect. From the NVR main display screen click on Setup in the top left-hand corner The Cameras menu is the first menu option beneath System Settings at the middle-top right-hand side of the Setup menu.
The IP address is listed beside each attached camera. Set the IP as: Please wait if there is a delay while the NVR system is configuring the port. From the Computer , plug a network line from the computer into an empty port on the NVRs embedded switch camera port. Suggest using camera port 16, if available. Click on networking. Select change adapter settings on the left side. Right click on the network adapter select properties.
Click on the Internet protocol version 4 and click on properties. Click on Apply. In a few minutes, the camera should be visible in the Cameras menu on the NVR. Supported Resolutions: x, x, P, P.
PS Model 1. Configure Your Router These directions are generic. Note: This information is case sensitive. Open Microsoft Internet Explorer. Type the IP address of the recorder into the Address bar. Type the User ID and Password of an authorized user. Click Connect to display your cameras. Click Security. Click Custom Level. Click Trusted Sites. Click Sites. Verify that the check box next to Require Server Verification is cleared. Click Add. Click Close. Desktop Mode If your computer has Windows 8, 8.
To view your recorder in Compatibility Mode: 1. When connection from within your local network, use the IP address of the recorder. When connecting from outside your local network, use the DDNS address. Connecting to Your Recorder 1. The default User is admin. The default password is PS Model can only be controlled with mouse.
PS Model Performing a firmware update is not always necessary if you are not currently experiencing any issues. To use the included remote controller, each recorder needs a unique Unit ID number that corresponds with a Remote Control number.
By default your recorder and remote controller are both set to ID 1. Click System. Click Remote Control ID. Click RS Setup. Select Unit ID and click Num. Unit ID Remote Controller ID 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Limited to 8GB size export per export Requires multiple exports if over 8GB is needed Remote export through web viewer on Windows PC This option could be slower depending on variables like the network speed, size of export, etc.
Not limited to any size other than the workstation hard drive you are saving to Will break up all exported files into MB files. Accessing Internet Explorer if you are already using Edge: When you first connect to the recorder it will show the following page informing you that Internet Explorer is required.
Click the Menu button and click "Open with Internet Explorer". A new Internet Explorer window will open to the same page explaining Internet Explorer is required. Unplug the NVR unit from the power source. On a static-free surface, remove the top cover of the NVR 6 screws total: 2 on top, 2 on either side.
After the top cover is removed the hard drive HDD tray is visible. Turn the HD tray over and remove the 4 screws from the assembly.
The new HDD is then formatted and starts recording immediately after the format is complete. Note: this does not apply to HD Bullet Camera. Within the first 10 minutes of plugging the camera in, locate the Reset button, press and hold for about 15 seconds.
Insert a spare Cat5 cable into the NVR switch. Click on Save. Click Save. The third octet of the IP address bolded is 50 plus the port number. Subnet mask Determine which port the camera is being plugged into. Each port has a different gateway. Please double-check settings before pressing Save.
If the information is entered incorrectly, you may not be able to connect to the camera unless you factory restore it again. From the NVRs local interface, right-click on the screen and the Menu icons appear at the top of the screen. Click Setup. The camera should begin streaming and displaying on the NVR screen within minutes. How do I update the firmware on my AvertX camera?
Download the camera firmware file to a computer and then unzip or extract the file. Access your camera through a web browser. When you have accessed the camera page, click Setup at the top of the page.
In the setup menu, click the Software upgrade tab on the left side of the page. Use the instructions below to remove the dome cover: Use the included Torx wrench to loosen the dome cover screws. Insert the Torx wrench into the mounting screw holes in the camera base.
Use the Torx wrench as a handle to separate the camera base from the dome cover. Remove the screw at the bottom of the front lens cover. Remote the front lens cover by gently tilting it up from the bottom. Remove the rubber gasket. Loosen the set screw. Turn the lens to focus your cameras. Tighten the set screw. Replace the rubber gasket. Replace the screw at the bottom of the lens cover. Use the included Torx Tool to loosen the two screws on the camera body.
Remove the dome housing. Need more help? Join the discussion. Was this information helpful? Yes No. Thank you! Any more feedback? The more you tell us the more we can help. Can you help us improve? Resolved my issue. Clear instructions. Easy to follow. No jargon. Pictures helped. Didn't match my screen. Incorrect instructions. Too technical. Not enough information. Not enough pictures.
0コメント